Professional ac repair services for homes and businesses in Kirby and surrounding Texas communities.
When your air conditioner in Kirby, Texas blows warm air, short cycles, or fails to start, KIC Refrigeration technicians identify the exact cause through systematic testing of the refrigerant circuit, compressor windings, capacitors, and control board. We restore reliable cooling performance with precision repairs that address the root problem, not just the symptoms.
Properties throughout Kirby (pop. 8,082) face unique demands when it comes to ac repair. Texas heating loads, cooling calculations, and the insulation levels and duct configurations found in Kirby homes all influence the approach we take. KIC Refrigeration tailors every ac repair project to the conditions your property actually faces — no generic solutions.
Choosing the right contractor for ac repair in Kirby, TX makes all the difference between efficient comfort and a system that short-cycles. KIC Refrigeration uses Manual J load calculations, installs to manufacturer specifications, and backs every project with a warranty. Call (866) 858-2961 to schedule your free assessment.
From initial contact to final verification — here is how we handle ac repair.
Our Kirby technician listens to your description of the problem, inspects the thermostat settings and wiring, checks the electrical disconnect and breaker, and performs a visual inspection of the outdoor condenser and indoor air handler for obvious issues like a frozen coil, tripped safety switch, or burned wiring.
We test capacitors, contactors, relays, and the compressor windings with a multimeter. We connect manifold gauges to measure suction and discharge pressures, calculate superheat and subcooling, and compare all readings to the manufacturer specification for your unit.
KIC Refrigeration performs AC repairs in Kirby, TX by the book. For electrical failures, we match the replacement part to factory specifications. For sealed-system repairs, we follow EPA Section 608 recovery procedures, braze with nitrogen purge, pressure test to 300 PSI, evacuate to 500 microns, and charge by weight — never by guessing or topping off.
Our Kirby technician verifies the repair by running the AC through a full cooling cycle. We measure supply and return air temperatures at the air handler to confirm a 16 to 22 degree split, check that suction pressure produces 35 to 45 degree evaporator saturation temperature, and verify the system cycles cleanly on and off.
Transparent answers about ac repair from our certified technicians.
AC repair in Kirby typically costs $150 to $500 for common component failures including run capacitors ($150 to $250), contactors ($150 to $350), condenser fan motors ($250 to $500), and blower motors ($300 to $600). Compressor replacement is the most expensive repair at $1,500 to $3,500 depending on unit tonnage and whether the system uses R-410A or older R-22 refrigerant. Evaporator coil replacement runs $800 to $2,500 including the refrigerant recovery and recharge. KIC Refrigeration provides a detailed written estimate with itemized parts and labor costs before beginning any AC repair at your Kirby property so there are no surprises on the invoice.
AC refrigerant recharge in Kirby costs $200 to $500 for R-410A systems at roughly $50 to $80 per pound, and $400 to $1,200 for older R-22 systems at $80 to $150 per pound due to the phaseout-driven supply shortage. However, simply adding refrigerant without finding the leak is a temporary and wasteful fix — the charge will leak out again in weeks or months and you will be back in the same situation. KIC Refrigeration always locates the leak first using electronic leak detectors and UV dye, repairs the leaking component, evacuates the system to remove moisture and air, and recharges by weight to the manufacturer specification. This approach fixes the problem permanently.
An AC that runs but produces little or no cooling is most commonly caused by low refrigerant charge from a leak, which reduces the suction pressure and causes the evaporator coil temperature to drop below 32 degrees, forming ice that blocks airflow completely. Other causes include a dirty condenser coil that cannot reject heat, a failed compressor that runs but does not pump refrigerant, a stuck or failed metering device — either a TXV or fixed orifice — that restricts refrigerant flow, or a blower motor running at reduced speed due to a failing capacitor. KIC Refrigeration connects manifold gauges at your Kirby home and measures suction pressure, discharge pressure, superheat, and subcooling to diagnose the exact cause.
Most AC repairs in Kirby are completed in 1 to 2 hours during a single service visit. Capacitor and contactor replacements are quick fixes that take 15 to 30 minutes of hands-on time. Fan motor and blower motor replacements take 1 to 2 hours including wiring and testing. Compressor replacement is the most time-intensive repair at 3 to 6 hours because it requires refrigerant recovery with an EPA-certified machine, compressor removal, new compressor installation, nitrogen-purged brazing, pressure testing at 300 PSI, evacuation to below 500 microns, and recharging by weight. KIC Refrigeration arrives at your Kirby home with a fully stocked truck to complete most repairs in a single visit.
Our reputation is built on certified technicians, honest pricing, and results that last.
"KIC Refrigeration installed a new furnace for us last winter. The team was respectful of our home, wore boot covers, and cleaned up everything. Top notch."
"AC tune-up before summer. Technician was early, finished in about forty-five minutes, and gave me a clean bill of health on the system. Easy process."
"Our AC went out on the hottest day of the year and they had someone here within two hours. Fixed it fast and explained everything clearly."